Page 3 of 3 FirstFirst 123
Results 31 to 44 of 44

Thread: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

  1. #31
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    So next I ground off the welds and bolted the hub to the rotor woth 5/8 bolts (same as the drill bit I am useing)
    Be ware of my BIG DOG complex

  2. #32
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    Then I had to grind the one side of there the 13 mm 12 point bolts attach to the knuckle to the hub a bit more so that the drill bit would pass. You only have to grind one spot because that part spins
    Last edited by XjJeepacorn; 05-01-2014 at 12:58 AM.
    Be ware of my BIG DOG complex

  3. #33
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.


    Then I set it up and clamped it down and drilled my one hole for the 5 on 4.5 pattern. I'll show yous guys what they look like tomorrow all drilled out and cleaned up tomorrow
    Be ware of my BIG DOG complex

  4. #34
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    !!!!
    Be ware of my BIG DOG complex

  5. #35
    Join Date
    Sep 2009
    Location
    Chico, CA
    Posts
    29,847

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    You are welding on cast iron there anyway Naomi, not like welding on steel. You just have to practice. The secret to a good weld is watching the puddle. Maintain a good puddle of molten steel and the weld will come out OK as long as you don't burn through. Congrats on the new bolt pattern
    Last edited by 4.3LXJ; 05-01-2014 at 09:47 AM.
    230 hp 4.3L Chevy
    Built 4L60E with manual lockout
    Atlas 4 speed
    Griffin radiator
    On board air
    Warn 9.5ti on custom bumper
    7.5" RE front and bastard pack rear on custom long arms
    30 gal gas tank
    lockers
    And a bunch of other stuff

  6. #36
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    yeah well it didn't really penatrate the rotor at all there were some small pits on it. The main thing is it held for the drilling and I just cut the welds with an angle grinder and then gave it a couple good whacks with a sledge and it came right off lol.

    I'm still going to have to weld those hub spacers on I guess baking the knuckles and then cooling them in sand is the way to go. Would you think heating it up with an Oxy Acetylene torch to hear them up quickley would be a better idea or no? Would that warp them maybe?
    Last edited by XjJeepacorn; 05-01-2014 at 12:03 PM.
    Be ware of my BIG DOG complex

  7. #37
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    I mean I don't wanna stick them on the bbq for an hour at 500 and not even get a slab of roast animal out of it!
    Be ware of my BIG DOG complex

  8. #38
    Join Date
    Sep 2009
    Location
    Chico, CA
    Posts
    29,847

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    If you are going to weld the spacers on the knuckles, I do believe the knuckles are cast steel and weldable. Also, bear in mind that the spacer needs only be held in place with a small weld. It is the hole and bolts that provide alignment
    230 hp 4.3L Chevy
    Built 4L60E with manual lockout
    Atlas 4 speed
    Griffin radiator
    On board air
    Warn 9.5ti on custom bumper
    7.5" RE front and bastard pack rear on custom long arms
    30 gal gas tank
    lockers
    And a bunch of other stuff

  9. #39
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    Yeah thought was to bolt it down to the hub and then weld a couple inch or so welds on all sides. Some people say you don't need to but JKS says to.tig weld it. I figure mig is a happy medium lol
    Be ware of my BIG DOG complex

  10. #40
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    ok!!! so the big trip is coming up I'm going state side on friday to star the upgrades



    so there are the knuckles with the spacers welded on.





    that is the jig I made to drill out the wj rotors.



    thats one of the drilled out rotors they just have a bit of surface rust on them nothing big no groves or anything but none the less I'm going to take them into work to give them a quick spin on the lathe.

    Be ware of my BIG DOG complex

  11. #41
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    so I bought

    - ruff stuff steering linkage and the chevy 1 tone tres as the title of the thread suggests!

    - jks track bar relocation bracket

    - clayton off roads adj track bar

    - us alloy ball joints

    - extended sway bar mounts

    - sirious offroad long arm kit

    - iron rock off roads 2nd steering damper.

    - tnt frame stiffeners + the extention stiffeners they sell that go all the way up to the coils.

    I think that about covers it unless I'm forgetting something??

    lol
    Be ware of my BIG DOG complex

  12. #42
    Join Date
    Sep 2009
    Location
    Chico, CA
    Posts
    29,847

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    Better get busy Naomi if you are going to get that done by Friday. Good Luck
    230 hp 4.3L Chevy
    Built 4L60E with manual lockout
    Atlas 4 speed
    Griffin radiator
    On board air
    Warn 9.5ti on custom bumper
    7.5" RE front and bastard pack rear on custom long arms
    30 gal gas tank
    lockers
    And a bunch of other stuff

  13. #43
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    no I'm leaving friday
    Be ware of my BIG DOG complex

  14. #44
    XjJeepacorn's Avatar
    XjJeepacorn is offline Level: Uber Jeep Cherokee Trailer Queen
    Join Date
    Mar 2013
    Location
    East York
    Posts
    1,249

    Default Re: WJ Brakes Knuckles and Chevy 1 Tone OTK Steering.

    and I have a feoend down there thats going to be helping me get everything done
    Be ware of my BIG DOG complex

Page 3 of 3 FirstFirst 123

Similar Threads

  1. Power Steering Pump vs. Steering Box Noise
    By Infidel Edition in forum OEM/Factory
    Replies: 2
    Last Post: 08-14-2013, 11:27 AM
  2. Old Chevy Trucks
    By prerunner1982 in forum General Talk
    Replies: 10
    Last Post: 06-11-2013, 10:39 AM
  3. D30 knuckles any one?
    By OhJeepers in forum Modified
    Replies: 9
    Last Post: 02-06-2012, 06:25 AM
  4. Chevy Small Block Conversion
    By brianwy77 in forum Modified
    Replies: 1
    Last Post: 04-07-2010, 11:37 AM
  5. Toot Tone
    By Mudderoy in forum Jokes!
    Replies: 3
    Last Post: 01-12-2010, 01:48 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •