Search:

Type: Posts; User: osfp; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    4,374

    Bosch fuel injector 111

    Is anyone running these type of injectors? I was thinking about upgrading my old ones, I see alot of rebuilt ones on Ebay but I don't know if they are really rebuilt about 100-140.00 bucks, or 230.00...
  2. Replies
    11
    Views
    4,092

    Re: Richmond powertrax

    They are seperated by springs, it has to have some clearence so it can slip when going around corners.
  3. Replies
    11
    Views
    4,092

    Re: Richmond powertrax

    Well I replaced the cam, and set it to where they say in the book, It ran but was running like a dog, so I pulled the cam out far enough to advance it one tooth and what a difference. It runs like it...
  4. Replies
    22
    Views
    14,644

    Re: MIG Welding Techniques

    The trouble with short circiut mig welding is that if you don't remove the mill scale the penitration isn't very good, you might have a really pretty weld but it won't hold squat. The cleaner the...
  5. Replies
    15
    Views
    9,427

    Re: bender and misc fab

    Nice job,
    I built one of these Tacky benders from (got trikes .com )but i just haven't bought any dies yet. Where did you get the latch? I want to build a roll bar and put it in my jeep.
    Is this a...
  6. Replies
    11
    Views
    4,092

    Re: Richmond powertrax

    I found the problem, the comp cam A6-260H-10 will not work with fuel injection!!!!!!! It says it right on the web site!!!!!! I don't know what todo now, pull the engine and put a new stock cam in...
  7. Replies
    11
    Views
    4,092

    Re: Richmond powertrax

    I don't know if it did? Tried to run it today and it feels like I'm pulling a boat anchor. I was wondering if the pcm has to be reset, Is there away to clear the pcm? I think I should have put a SBC...
  8. Replies
    11
    Views
    4,092

    Re: Richmond powertrax

    I didn't build the engine I had a good engine shop do it, I would amagine that it is set to factor marks, He told me he had put acouple of these cams in with no problem. Whem i put the distributor in...
  9. Replies
    11
    Views
    4,092

    Richmond powertrax

    I need some help, I put in a richmond power trax no slip locker in my 8.25.
    first of all the directions do not say to reuse the spider gear thrust washers do you or don't you? and the biggest...
  10. Replies
    0
    Views
    2,319

    Pace setter header?

    Hello,
    I bought a pace setter header for my 4.0. My question is how do you get the center lower bolt in and torque it? Also do you know what the torque rating is on the manifold bolts? I heard it...
  11. Replies
    37
    Views
    14,643

    Re: Thoughts & Opinions...

    Galaxy radios pricey but worth it look on ebay and get one tuned and peaked I use Galaxy 949 works great. I also have cobra 25, and uniden with the weather channels both good radios.
  12. Thread: Dual Antenna's?

    by osfp
    Replies
    27
    Views
    11,164

    Re: Dual Antenna's?

    Just my 2c the best placement for your antenna is right in the middle of your roof, that way yo use the total ground plane of your rig, mounting on the side makes the antenna more directional, and as...
  13. Thread: Engine Knock

    by osfp
    Replies
    21
    Views
    7,960

    Re: Engine Knock

    Mine sounded like that and I thought it was a rod knock but it was torqure converter bolts loose. Just had the engine pulled down and the bearing were all good
Results 1 to 13 of 14