Search:

Type: Posts; User: NW99XJ; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Shock Mount Fix

    by NW99XJ
    Replies
    7
    Views
    3,256

    Re: Shock Mount Fix

    Cut off the remainder, drill a hole, stick a longer bolt thru, and be done... you want to go the extra mile then weld the head to the back side of the mount. (that would be the RIGHT way to go about...
  2. Replies
    16
    Views
    13,743

    Re: Big things happening at Ironman

    GOOD LAAAWWRD!
    Thats looking like some pure beef Andy!
    Wow! ...what a brace system!
    This looks better than anything else out on the market currently.
    Nicely done Ironman Andy!
  3. Replies
    9
    Views
    9,126

    Re: U Connect bluetooth audio delay

    There will always be some degree of latency with bluetooth audio. It's just the nature of the beast. Just as you will never get true HD audio from a bluetooth stream. There;s just too much data that...
  4. Replies
    4
    Views
    4,392

    Re: Black box under neight in front of fuel tank?

    Most likely vapor recovery.
    There was some retarded EPA mandate a while back that forced gas stations to start putting those rubber sheaths around the pumps nozzles, and vapor recovery systems in...
  5. Replies
    11
    Views
    4,535

    Re: Front driveshaft problem

    Pictures always help.
    Flip that driveline around (like in the picture Mudderoy posted) and you "should" be fine.
    But like the others said... I would consider swapping out that low pinion dana 30...
  6. Replies
    11
    Views
    4,535

    Re: front driveshaft problem

    Sound more like a pinion or shaft issue than a problem with the yoke.
    Unless you have clocked your T-case, the front yoke (as it is stock) should be adequate enough for anything up to 8" of lift...
  7. Thread: Vacuum?

    by NW99XJ
    Replies
    5
    Views
    1,384

    Re: Vacuum?

    I'm wondering if the TPS (throttle position sensor) is jacked up.
  8. Replies
    6
    Views
    4,162

    Re: Looking for a basic 3" lift kit advice

    At The 3” range of lift, there’s a couple things that will need to be taken into consideration.
    First and foremost is your budget. Knowing what you have to work with will help determine just how...
  9. Replies
    2
    Views
    4,482

    Re: Harness replacement

    The short answer is that it depends on the manufacturer of the plug (the plastic part the pins go into)
    the gauge of wire, and the if it’s a weather resistant plug or not.
    The “sex” of the...
  10. Replies
    13
    Views
    5,432

    Re: Adding additional switches ideas

    Always glad to see someone else's take on switch placement, and what they come up with.
  11. Replies
    13
    Views
    5,432

    Re: Adding additional switches ideas

    Unfortunately I have a late model, so my switch panel pics wont help you much.
    But if you want some other options, check out PRIME 4x4
    They have some cool stuff for you to buy, or that might give...
  12. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    While sitting at my desk today (08/31/2015)
    I was presented with what I THOUGHT I was going to be able to take home on Friday.
    My now bored and matched throttle body and spacer!
    :woot:...
  13. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    The only left to do was install the newly cleaned inserts with their new clips back into the valve cover.
    Got a VERY NICE surprise, and even had the girlfriend come help out. :thumbsup:...
  14. Replies
    338
    Views
    66,865

    Valve Cover Replacement - Aug/Sept. 2015

    With the cover cleaned and set aside, it was time to address the inserts.
    The old retaining clips needed to be separated from the metal inserts.
    At first I used a small thin screw driver, holding...
  15. Replies
    338
    Views
    66,865

    Valve Cover Gasket Replacement - Aug/Sept. 2015

    Some of the replacement valve cover gaskets out there do not come with new inserts.
    I opted to get the one that does. It's a little more, but worth it in the long run....
  16. Replies
    338
    Views
    66,865

    Valve Cover Replacement - Aug/Sept. 2015

    Next up was some detail work....
    The surfaces that ANY gasket are to be in contact with should be free and clear of any grease, dirt, debris,
    ...or anything that could otherwise compromise the...
  17. Replies
    338
    Views
    66,865

    Valve Cover Gasket Repair - Aug/Sept. 2015

    Once you get around to the other side, there is more hardware that will need to be removed, before you can get to the bolts.
    The heater hose retainer clip is one such piece, it too slides off the...
  18. Replies
    338
    Views
    66,865

    Valve Cover Gasket Repair - Aug/Sept. 2015

    More work was done over the weekend....
    The Valve Cover Gasket was in need of replacement, luckily for me, i was swimming in FelPro at this point. ...
  19. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    Hmmmm......
    "While i'm in there".....

    http://jeep.blackonyx.net/forum/Hesco2xtrouble.jpg
  20. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    The only problem with putting a hose over then and clamping it is the clearance between where the top of the hose & clamp would be and the bottom of the radiator cap.
    It;s like "right there"...
  21. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    Thats how it all started for me too!
    At least this thing is just a toy now, so I can get away with making plans like that....the problem I have is execution and cash flow. (not necessarily in that...
  22. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    The other things I have on my mind now that half the engine is torn apart....
    Valve Job.... since I need to replace the valve cover gasket anyways... "while you're in there"
    ...which is why I had...
  23. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    My plan.... thus far...is this:
    Cut/shave/grind/file the remaining (plastic) nipple off to this point:
    http://i1104.photobucket.com/albums/h328/jbchill1/Header%20Repair%20Aug%202015/radcapmod.jpg
    ...
  24. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    Some of you may have heard on a recent episode of The Jeep Talk Show, that my Jeep gave a slight fit of overheating on my way back from the Salem Jeepers Summer Jam.
    I MAY have found part of the...
  25. Replies
    338
    Views
    66,865

    Re: 1999 XJ DD & Weekend Warrior

    Brandon set to task, and made short work of it all:
    http://i1104.photobucket.com/albums/h328/jbchill1/Header%20Repair%20Aug%202015/20150823_141359.jpg
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4