Search:

I wonder if a left front will work in the rear????

When I try to use the window crank the window only goes down about an inch or so and then it makes a racketing sound. After that it will not round up or down. I took the panel off and pushed back up,...

What would be everyone's thoughts on a "How to" article on this when I get around to fixing it???? Dan

Thanks Nick, that was a good repair write up. I will try to get it apart and see if I can find a part number on it for you James. Dan

Thanks for the help so far everybody. On mopar's website I came up with two numbers, this one is no longer available 55076293AC and this one is for the left side but does not state if it is front or...

Moparamerica.com carries a lot of new parts if this helps. DanXJ97

I have 1997 Cherokee four door and I need a left rear manual window regulator, mopar shows that they do not have it new. I can't find one used in Phoenix, does anyone know where I can start looking??...

No pressure in tank and what I found out is it needs a spring in the tank. It only does it if over 3/4 full and then it quits. Dealer says no big deal with you can live with the noise. It just a Jeep...

I have 97 Cherokee 4.0 auto trans about 110,000 miles on it. When I shut it off I can hear a gurgling noise from the gas tank. The stock heat shield is in place and I have a new gas cap on it. I have...

I'm going to do a lot of frontend work on my 97 XJ and I figured that I would install front lower control arm skid plates while I was at it. I can still my factory control arms, I read in one place I...

I have 1997 XJ with a D30 front axle and it needs a pinion seal. Is the pinion shaft set with shims or crush collar? Thanks, Dan :rolleyes:

Hi folks, Dan here again with a new problem. I have a 1997 Jeep Cherokee, 4.0 engine, auto trans. Check engine light came on today and my code scanner gave me P0132 which means problem with O2 senor....

Two questions, who made them and do you take paypal? Thanks, Dan

Thanks for the reply, smittybilt XRC looks like a good bumper. I like the way it mounts on rear uni-rail and it comes powder coated. I found several websites that has it in my price range. Any...

My wife OK'd a new rear bumper for me. It's a 1997 Cherokee, 4x4, auto trans, 6.0 engine. I would like one with D-rings and hitch built in, I have trusted the judgment of people here on this site and...

I have a 1997 Cherokee with the D30 front axle and would like the toe-in specs please. Thanks, Dan

It can be either It doesn't matter. I thought it might easier to go aftermarket and be able to get parts but factory is fine too. And from my experience with my 97 it does seem to have a lot of...

I have a 1997 Cherokee 4.0, auto trans, 4x4 and I would like some information on installing power remote door locks. Any aftermarket kits any good? Thanks for any input. Dan :rolleyes:

Maybe I'll try one of the old Plymouth roadrunner horns. That would be close to what I'm looking for.

I have bought and sent back three sets of horns because they are not the old style "beep beep" jeep horns. Anybody know where and what part number they are??? People tell me on the phone yes we got...

OK I took apart my whole front axle and found a bad carrier bearing and had both of them replaced. I going to put in new axle u-joints and while I had the diff out I installed my Lokka, took about an...

Hey Keegirl96 Dan here and I would like to know about how many miles you have on your aussie locker. I was wondering how long they last. Thanks

I have a 97 4.0 4x4 Cherokee and I will be putting new JKS disconnects on the stock frontend. I was wondering if I have to install longer brake lines on it and if I do how much longer do they have to...

Thanks for the input so far, I try to avoid heavy rock crawling if possible with a stock setup. The one aspect of wheeling is you never know what's around the next turn so I would like to be ready...

Hi everyone, I have a 1997 Cherokee 4.0 auto trans and it did not have a skid plate on it when I got it. Any certain brand that is recommended or just get one made of 3/16 metal and don't lose any...