Search:

Im going to try to pressure bleed with a air pressurized system next. I hope its just air and not more parts lol Thanks for the help

Pumping it while it is running does not give it any more pressure. once the jeep is running nothing pressurizes the pedal. I even adjusted the rod thinking it was hanging the master cylinder open and...

Vehicle is an 88XJ. I put on extended steel braided lines that came with my 6.5 iro long arm kit. After it was all installed i went to bleed them only to notice a leak between the master cylinder and...

Here is a little side note when doing re gear on the Chrysler 8.25 axle. I went with the 4.88 usa standard gear set and also had to order a YUKON notched crosspin. Thats one thing i did not know and...

You are right bout the carrier. Pre 97 is 27 spline from the factory. After that stock 29 spline. I purchased a 29 spline carrier and the housing and everything else is the same. I believe the seals...

Just placed a order for axle stuff. Going with 4.88s.

Sent from my SPH-L900 using Tapatalk 4 Beta

Here is the final stance once all suspension mods were added.



Sent from my SPH-L900 using Tapatalk 4 Beta

Cleaned the gummed up throttle body today. Also changed plugs and wires and cap and rotor. Gave it a smoother idle.

Put on iron rock offroad coil spring spacers also. To remove stock bumpstop use...

Im in blythe California. ...anyone else that far south? Got a 89 xj with iro 6.5 long arm kit and 33 wrangler kevlar mtr. Just working on getting the chrysler 8.25 under it and my dana hp30. Soon it...

A picture of the chrysler 8.25 rear end for my 88xj. Coming soon a 29 spline transformation involving Ten alloy axles and a lock rite locker and 4.56 gears

Sent from my SPH-L900 using Tapatalk 4...

I found one and paid $100 for it. Not sure if thats good or bad but i found one and bought it haha. Plan is to run the 27 spline open setup until i get all my parts then build it into a 29 spline...

Is there any good sources out there to get used 29 spline carriers? Im going to change my 27 spline to 29 spline for strength and im going to use a lock rite locker so i need a 29 spline carrier. Not...

Yea the rear end casting is way beefier i did notice that. Well im thinking about just ordering 29 spline chromoly axles and a locker for the 29 spline. Gonna gear it to 4.88 or 4.56 , not quite sure...

also i got this rear end complete drum to drum for 200 dollars so i think thats a decent price

Supposedly came out of a 96 XJ but my research says that some late 96's came with 29 spline or 27 spline and everything after 96 is 29 spline. Just in a debate with someone who is trying to say i...

Hey everybody i need help with a Chrysler 8.25 i just purchased and get get any info on the casting numbers online. On the caps it says 3723574 and wn26....anybody that can help me identify the axle...

The d30 was bent severly and had to replace also. The original d35 rear end had a blown ring and pinon so i acquired another d35 from a donor cherokee , i was excited because this d35 has the factory...

Is there any way to bend the Dana 35 back straight without comprimising its strength? Im thinking get it bent straight and sleeve or truss to add stregth. Any ideas suggestions appreciated.

77 Camaro , weighs 3300 lbs with me in it , Chevy 350 that is .30 over with flat top keith black pistons , isky racing .511 lift cam , vortec heads with 2.02 , 1.60 one piece swirl polished stainless...

Here is the other hobby i have besides building my XJ. Just wanted to share with you folks.

Well its been an uphill fight so far. Replaced the blown up rear end only to find that its replacement was bent. I was really excited on the new rear end as it was a posi unit. Got the long arm kit...

pictures of the front end parts!

Pic of the new wheel and the new rear suspension and new rear end mounted in it.
progress!

Upload is not working right now srry. pics soon. Mods I have going so far are a 6.5 inch IRO long arm kit. 33x12.50x15 goodyear wrangler kevlar mtr's with pro comp 52 series steel rims. Grant...

Here is what im starting with.