Cut off the remainder, drill a hole, stick a longer bolt thru, and be done... you want to go the extra mile then weld the head to the back side of the mount. (that would be the RIGHT way to go about...
Tapatalk is active for this site! Just go to your phone's store to download and install.
Type: Posts; User: NW99XJ; Keyword(s):
Cut off the remainder, drill a hole, stick a longer bolt thru, and be done... you want to go the extra mile then weld the head to the back side of the mount. (that would be the RIGHT way to go about...
GOOD LAAAWWRD!
Thats looking like some pure beef Andy!
Wow! ...what a brace system!
This looks better than anything else out on the market currently.
Nicely done Ironman Andy!
There will always be some degree of latency with bluetooth audio. It's just the nature of the beast. Just as you will never get true HD audio from a bluetooth stream. There;s just too much data that...
Most likely vapor recovery.
There was some retarded EPA mandate a while back that forced gas stations to start putting those rubber sheaths around the pumps nozzles, and vapor recovery systems in...
Pictures always help.
Flip that driveline around (like in the picture Mudderoy posted) and you "should" be fine.
But like the others said... I would consider swapping out that low pinion dana 30...
Sound more like a pinion or shaft issue than a problem with the yoke.
Unless you have clocked your T-case, the front yoke (as it is stock) should be adequate enough for anything up to 8" of lift...
I'm wondering if the TPS (throttle position sensor) is jacked up.
At The 3” range of lift, there’s a couple things that will need to be taken into consideration.
First and foremost is your budget. Knowing what you have to work with will help determine just how...
The short answer is that it depends on the manufacturer of the plug (the plastic part the pins go into)
the gauge of wire, and the if it’s a weather resistant plug or not.
The “sex” of the...
Always glad to see someone else's take on switch placement, and what they come up with.
Unfortunately I have a late model, so my switch panel pics wont help you much.
But if you want some other options, check out PRIME 4x4
They have some cool stuff for you to buy, or that might give...
While sitting at my desk today (08/31/2015)
I was presented with what I THOUGHT I was going to be able to take home on Friday.
My now bored and matched throttle body and spacer!
:woot:...
The only left to do was install the newly cleaned inserts with their new clips back into the valve cover.
Got a VERY NICE surprise, and even had the girlfriend come help out. :thumbsup:...
With the cover cleaned and set aside, it was time to address the inserts.
The old retaining clips needed to be separated from the metal inserts.
At first I used a small thin screw driver, holding...
Some of the replacement valve cover gaskets out there do not come with new inserts.
I opted to get the one that does. It's a little more, but worth it in the long run....
Next up was some detail work....
The surfaces that ANY gasket are to be in contact with should be free and clear of any grease, dirt, debris,
...or anything that could otherwise compromise the...
Once you get around to the other side, there is more hardware that will need to be removed, before you can get to the bolts.
The heater hose retainer clip is one such piece, it too slides off the...
More work was done over the weekend....
The Valve Cover Gasket was in need of replacement, luckily for me, i was swimming in FelPro at this point. ...
Hmmmm......
"While i'm in there".....
http://jeep.blackonyx.net/forum/Hesco2xtrouble.jpg
The only problem with putting a hose over then and clamping it is the clearance between where the top of the hose & clamp would be and the bottom of the radiator cap.
It;s like "right there"...
Thats how it all started for me too!
At least this thing is just a toy now, so I can get away with making plans like that....the problem I have is execution and cash flow. (not necessarily in that...
The other things I have on my mind now that half the engine is torn apart....
Valve Job.... since I need to replace the valve cover gasket anyways... "while you're in there"
...which is why I had...
My plan.... thus far...is this:
Cut/shave/grind/file the remaining (plastic) nipple off to this point:
http://i1104.photobucket.com/albums/h328/jbchill1/Header%20Repair%20Aug%202015/radcapmod.jpg
...
Some of you may have heard on a recent episode of The Jeep Talk Show, that my Jeep gave a slight fit of overheating on my way back from the Salem Jeepers Summer Jam.
I MAY have found part of the...
Brandon set to task, and made short work of it all:
http://i1104.photobucket.com/albums/h328/jbchill1/Header%20Repair%20Aug%202015/20150823_141359.jpg
...